Abstract
The small punch (SP) test is one of the small specimen test techniques, and standardization of the SP test method for evaluating the mechanical properties of metallic materials is in progress. In this study, the impact transition temperature of reactor pressure vessel steels (RPV) in nuclear power plants was estimated..... More

Abstract
A method for evaluating residual stress using an instrumented indentation test was developed some decades ago. More recently, another method was developed, using a Knoop indenter. The conversion factor ratio, which is one of the key factors in the evaluation algorithm, has been taken to be 0.34, although this value..... More

Abstract
Cu-Ni-Si alloys were strengthened by Ni₂Si intermetallic compound precipitation in a Cu matrix during aging. The Cu-6 wt% Ni-1.4wt%Si alloy was prepared by water quenching (solution treatment) or air cooling (homogenization treatment) after heating 980 ^oC for 2 hours and aging at 500 ^oC for 6 hours. After maintaining a..... More

Abstract
Polycrystalline diamond compact (PDC) has excellent wear resistance, high impact resistance, superior fatigue properties, and has been used in the oil and gas drilling industries. This study investigated the effect of Co leaching on the microstructure, vertical turning lathe (VTL) wear properties of PDCs manufactured by high-temperature and high-pressure (HTHP)..... More

Abstract
The subject of this study was a bronze sword excavated from the early Iron Age area of Sinpung site in Wanju. SEM-EDS, FE-EPMA and Raman Micro-Spectroscopy analysis methods were applied to investigate the manufacturing techniques and corrosion characteristics. The results of the analysis indicated a casting structure composed of both..... More

Abstract
We report on the phase transition behavior and thermoelectric transport properties of Zn-doped Cu₂Se. Cu₂Se is comprised of nontoxic, low-cost and abundant elements, and has been attracting attention because of its very high thermoelectric performance, ZT, at high temperatures. Many studies have reported enhanced ZT in impurity doped Cu₂Se, however,..... More

Abstract
Tungsten carbides are quite attractive for their superior properties, e.g., high melting point, high hardness, high thermal and electrical conductivities, and relatively high chemical stability. Tungsten carbides with a binder metal, for example Co or Ni, are mainly used to produce cutting tools, nozzles and molds in the composite form...... More

Abstract
A stripping solution with thiourea, iron(III) sulfate, and sodium dodecyl sulfate(SDS) was employed to strip Ni-based 14 karat white gold alloys, and the formation of the NiS byproduct and elimination of passivation were investigated in the presence of 0.0-0.2 g/L SDS. White gold alloy samples with a flat shape were..... More

Abstract
In this study, we report how Cu doping can modify the thermoelectric performance of p-type Bi_0.5Sb_1.5Te3 and Bi_0.4Sb_1.6Te3 thermoelectric alloys, including their electronic and thermal transport properties. For electronic transport, the power factors of both Bi_0.5Sb_1.5Te3 and Bi0.4Sb1.6Te3 compositions were increased by Cu doping. The origins of the enhanced power..... More

Abstract
Technologies for pedestrian safety are increasingly emphasized by Automakers in advance of autonomous driving vehicles. A Night Vision System attached behind the front grille can reduce fatal accidents, especially during the nighttime, however, consumers may hesitate to adopt such systems on account of their high price. High-cost Germanium is used..... More

Abstract
Electropulse-induced heating has attracted attention due to its high energy efficiency. However, the process gives rise to a nonlinear temperature variation, which is difficult to predict using a traditional physics model. As an alternative, this study employed machine-learning technology to predict such temperature variation for the first time. Mg alloy..... More

Abstract
In this study, solidification cracking behavior and susceptibility in dissimilar cladding of Inconel alloy FM 52, 308L stainless steel to carbon steel, was investigated by submerged arc welding and transverse−Varestraint testing with gas tungsten arc welding. The effect of cladding conditions on cracking behavior and susceptibility was extensively evaluated, and..... More

Abstract
The powder-alloyed metallic sheet foam manufacturing process has the advantage of being able to control pore shape, size, and distribution more easily and homogeneously than conventional foam manufacturing processes. The effects of strain rate and tensile direction on the mechanical properties of Ni-Cr-Al superalloy foam fabricated by powder alloying method..... More

Abstract
New technologies need to be developed in the ironmaking process to reduce carbon dioxide emissions. To achieve this, in recent years steelmakers have been working to reduce coke usage by increasing thermal energy efficiency. However, it is very difficult to reduce coke consumption while maintaining production, because the level of..... More

Abstract
Polyurethane foam (PUF) is one of the most well-known cellular materials and is widely employed in various industrial and biomedical fields thanks to its many advantages. These include mechanical and material characteristics such as low density and thermal conductivity, and high specific elastic modulus and strength. Despite of these advantages,..... More

Abstract
TiO₂ nanostructures were synthesized using a thermal evaporation method without a catalyst. TiO powders mixed with graphite powders were used as the source materials. The synthesis process was performed in air atmosphere at 1000 °C. When the mass ratio of TiO/graphite in the source material was 2:1, TiO₂ nanowires and..... More

Abstract
Layered post transition metal chalcogenides such as SnSe, SnSe₂, In₂Se₃, and In₄Se₃ have attracted attention as promising thermoelectric materials due to their intrinsically low lattice thermal conductivities. Recently, n-type indium selenide (InSe) based materials have also been suggested as good candidates for thermoelectric materials by optimizing their electrical properties, i.e.,..... More

Abstract
Tetrahedrite (C₁₂Sb₄S₁₃) has attracted attention as a p-type thermoeletric material with very low thermal conductivity induced by the anharmonic oscillation of Cu due to the lone-pair electrons of Sb. Many studies have been conducted to improve its thermoelectric performance by partially substituting the transition elements for the Cu sites. In..... More

Abstract
We report the thermoelectric transport properties of n-type Bi₂Te_2.7Se_0.3 compounds prepared by oxide-reduction process. The oxide-reduction process is a recently developed method that can synthesize Bi2Te3-based compounds using only oxide starting materials, which is advantageous in terms of the diversity of the starting materials and cost efficiency. In this study,..... More

Abstract
In this study the correlation between bainitic microstructure and the low-temperature toughness of high-strength API pipeline steels was discussed in terms of crack initiation and propagation in the microstructure. Three types of API pipeline steels with different bainitic microstructures were fabricated using varying alloying elements and thermo-mechanical processing conditions, and..... More

Abstract
Tetrahedrite has low lattice thermal conductivity because of the lone-pair electrons of Sb, which cause the Cu atoms to vibrate at a low frequency and high amplitude. The synthesis of tetrahedrite compounds by conventional melting methods requires a long-time reaction and annealing. However, a homogeneous and solid-state synthesis can be..... More

Abstract
In this study, Fe₂O₃ photoelectrode thin films were grown on fluorine-doped tin oxide substrates at various temperatures ranging from 145 to 220 oC using modified chemical bath deposition. The morphological, structural, electrical, and photoelectrochemical properties of the resulting Fe₂O₃ photoelectrode were analyzed using field emission scanning electron microscopy, X-ray diffraction,..... More

Abstract
Three kinds of Ni-based single crystals with the compositions of 63.8Ni-7.5Cr-5.1Co-4.8Al-1.9Mo- 0.9Ti-3Re-11.8Ta-1.2W, 61.4Ni-7.4Cr-5Co-4.8Al-1.8Mo-0.9Ti-3.1Re-11.6Ta-4W, and 60.9Ni-7.5Cr-5Co-4.8Al- 2Mo-1Ti-2.9Re-10.9Ta-1.2W-3.8Ru, in wt%, were cast in a Bridgman furnace. In the cast alloys, Cr, Co, Re, Mo, W, and Ru became microsegregated in dendrites consisting of γ-Ni, while Ni, Ta, and Al microsegregated in interdendrites..... More

Abstract
In this study, the effects of nickel and copper on the mechanical and thermal properties of Al-Si alloys were investigated, for different alloy compositions. Thermodynamic calculations were carried out to predict the alloys’ solidification behavior (solidification temperature, solid fraction and physical properties (density, thermal conductivity, elastic modulus, bulk modulus)). The..... More

Abstract
Materials with very small dimensions exhibit different physical and mechanical properties compared to their bulk counterparts. This becomes significantly important for the thin films that are widely used as components in micro-electronics and functional materials. In this study, a chromium (Cr) thin film was deposited on a silicon (Si) wafer..... More

Abstract
In this study, the effect of post annealing time on the physical properties of NiTe₂ thin films with 2D structure deposited by co-sputtering was investigated. After heat treatment for 10 min, nickel ditelluride thin films with a composition of Ni : Te = 1 : 2 exhibited transmittance of 46%..... More

Abstract
Quarternay carbides of Ti₃Al_xSi_1-xC₂ (x=0.3, 0.5, and 0.7) were oxidized at 400, 600, and 800 °C for 0.5-6 months in order to study their long-time oxidation behavior in air. When they were oxidized at 400-600 ^oC for 0.5-3 months, oxidation proceeded relatively slowly with moderate weight gains. However, further oxidation..... More

Abstract
In recent automobile trends, the functions of opening and closing the vehicle door are accomplished by touch sensor and smart-phone NFC (Near Field Communication) systems. These convenience features are incorporated into the outdoor handle. However, this function can’t be used when chrome plating is applied to this part for design..... More

Abstract
A superelastic titanium alloy was subjected to uniaxial tensile deformation at room temperature. The microstructural evolution and deformation mechanisms of the superelastic titanium alloy were investigated by electron backscatter diffraction (EBSD) and X-ray diffraction (XRD). Multiple deformation mechanisms including stress-induced martensitic transformation (SIMT), dislocation slip, {332}<113> and {112}<111> mechanical twinning..... More

Abstract
Al 3003 alloy was manufactured by strip casting process, and the effect of post heat-treatment on tensile and fatigue properties was investigated. The strip cast Al 300 alloy exhibited a unique globular shaped rapid-cooled solidification structure, and the microstructural characteristic remained after heat-treatment. Asstrip cast (F) and heat-treated (O) alloys..... More